Wednesday, 18 November 2026

Star Wars Legion Scale Droid MTT

 Star Wars Legion Scale Droid MTT

The Separatist Alliance Droid MTT - a whole army in a can!

Once I start an army project, I usually decide early on what the scope will be and just build to that limit so that I don't fall down the slippery slope of the infinite collection.

With my Separatist Alliance Droid army for Star Wars Legion, I wanted to include their most recognisable units and vehicles, which included the iconic MTT (Multi-troop transport) first seen in Episode I almost 30 years ago.

At first glance, this massive vehicle does look a bit like a brick, but it is actually quite a nuanced design! The shape is immediately reminiscent of a mammoth skull, with a huge lumpen top section where the Droid command crew are housed, a massive anti-grav engine unit giving it quite a wide tail section and finally a cavernous internal transport bay at the front.

I always felt like this massive transport was the prequel generation's Jawa Sandcrawler with it's sweeping panelled sides and implacable slow movement, but the two couldn't be more different in function. Where the Sandcrawler is a unique, ramshackle mobile housing estate, the MTT is a mono-tasked mass produced behemoth, existing only to deploy masses of Droids to the front lines as efficiently as possible.

As Atomic Mass Games don't currently make a model of the MTT, I started doing my homework on the vehicle to determine exactly how big it was, how that worked out in 28mm / 1:48 scale and whether there were any toys or model kits which were close enough to represent this monster. As you're reading this article, I think the answer to that question is pretty self evident!

The Droid MTT is noted as being 35.94 meters long and 10.54 meters tall which would work out at roughly 75cm long and 22cm tall. Although it's pretty difficult to get exact measurements from the internet alone, I was able to determine that the Hasbro MTT toy was approximately 76cm long putting it right in the sweet spot for Star Wars Legion despite being designed for use with 3.75 inch action figures. Frequently Star Wars toy vehicles are re-scaled and in this case it worked in my favour!

I managed to procure a second hand MTT for a very reasonable price and straight away, when comparing it to some Legion scale miniatures, I could tell that it was about right!

Stripping down the chassis

The next stage of the project wasn't just to repaint this behemoth - I had decided before even buying the toy that I was going to strip it down and convert it to carry all of the troops and smaller vehicles for my Droid army. There was a lot of components inside the toy which I'd need to completely remove and replace with additional internal details, floor panelling and work out exactly how much of the army would fit inside.


The toy had plenty of hatches and compartments, but due to the Droid deployment mechanism and REAL MOVIE SOUNDS, I'd need to gut the carrier in order to fit more than a couple of miniatures inside.


As you can see, the MTT is pretty well constructed and after removing a gazillion screws and tabs, I could finally access the mechanism and electronics inside. Then brutally rip them out.

The above picture shows the various parts I removed from the toy and just from the size of the AA batteries, you can see how much space it all took up!

This are all of the basic panels from the toy all stripped down and laid out with the screws I needed to hang on to for the later rebuild. The next stage would require some light surgery...

Converting the interior

In order to turn this from a toy into a terrain piece and carry case for my Droid army, I needed to remove, convert and replace some portions of the interior.
 


The section highlighted in the above images had to be removed in order for me to create access to the larger deck space I would be constructing inside now that all of the toy gubbinz such as motors and wires had been removed. These sections live under the side door panels and were't big enough to house any miniatures, so those nicely detailed walls just had to go!

Cutting these two areas out wasn't exactly straightforward, but I did eventually manage to get the areas nicely cleaned up. This took a lot of low-speed Dremel time with a saw blade and multiple grinders. You have to be extremely careful with this type of plastic as it melts, coats and ruins your tools if you try to get through it too quickly.

As well as the walls under the side door panels, I also had to remove, cut down and then re-add the battery compartment cover which sits right at the bottom rear of the vehicle.
In order to maximise the flat surface area to re-floor as a troop bay, I essentially had to cut and grind away the majority of the battery casing from the inside of the toy - the external cover only need a bit of adaption to make it an acceptable plug for the gaping hole!
As you can see from the inside, the air vents on the battery plate where covered with some plasticard to seal it up nicely. I also had to clip and grind down any screw pillars within the central area while leaving the outer screw ports untouched so it could be re-assembled.


Once I had flattened the rear troop bay, I created a floor insert from Foamex to level it all nicely and even built a stepped level for General Grievous to stand on at the back - this was partly due to some functional parts I couldn't remove from the original structure and partly because it just looked cool!

Working out the troop placement inside the bay was important as I needed to make sure that nothing would be caught by the walls or hatch mechanism when rebuilt.

Once I had etched some nice floor panel details into the floor surface and plugged / filled any unsightly holes, I added self-adhesive steel plates to the flooring so that all of my miniatures could be safely magnetised inside for transport!


The top bays received very similar treatment with gap filling, new flooring, wall detailing and steel plates for magnetising troops. There was also a small bonus compartment which originally housed the REAL MOVIE SOUNDS components. It wasn't large enough for actual miniatures, but I re-floored it in case I needed somewhere to store dice, tokens or a small bag of emergency Haribo!

Building the Deployment Mechanism

The original mechanism inside this toy was extremely large and heavy, filling almost all of the internal space. I could have simply extended the flooring as I did in the rear, but I wanted to go one step further by utilising the existing rail slot on the base plate and the side slots which anchored the old mechanism on the walls. Obviously I wanted to be able to store my B1 Battle Droids en-mass in the front section just like in the movies - well, almost like in the movies as mine would all be standing up, instead of being folded up in racks, but you get the point!


First I built a thick Foamex rod to sit inside the rail channel - this would form the support spine for the lower tray, but also had to slide out and back in easily as well as allow me to easily remove the tray to make loading and unloading my Droids easier. It was to be a functional case after all!

To help the spine run along the rail smoothly, I reinstalled the tiny plastic wheels which helped the original plastic mechanism and cut a thin locator channel into the centre to help keep it straight and level as the wheels pressed into the indent.

To hold the spine down, I created two flush support clips at the mid-point and added a styrene stopper on the thinner end section which is tall enough to arrest the motion when the beam is straight, but moves easily under the support clips for removal when tilted upwards.

This did all take a lot of tinkering, test fitting and adjustment, but now runs very smoothly with no wobble as it's very securely anchored.


The next step was to cut a foamex section exactly the right width for the compartment, etch floor panelling onto the surface and add more metal discs for my B1 Droids to magnetically clip to. Note that I deliberately bought thin metal discs which fit inside the rim of the bases and ensured that the magnet depth still allowed the base rims to touch the floor. That stops any sliding around and keeps everything nice and secure!


The second level required a more complicated base plate with side rail slots which fit exactly into the side rails of the toy. This took quite some time to work out as it needed to provide grip and support on the sides which still being able to move in and out easily. The rear section again has a stopper which uses a slanted plastic section on the toy to provide a natural stopping point which can be circumvented with a gentle wiggle to free the plate for removal.

Hatch locking mechanism
The front door hatch would normally rely on the huge bulky mechanism of the rack to push and hold it open. I didn't want to immediately destroy my lovingly painting B1 Droids by smashing them in the face with a heavy plastic door, so I had to come up with a mechanism to hold it open.

In the end, I came up with a simple locking pin which can be access via the command deck hatch. It's not my favourite part of the build and it was a massive pain to construct, but it's functional and it works, so not much more to say! 

Although I didn't photograph it, while making this mechanism, I also added tiny metal pins to all of the hatch joints as they only had small plastic studs which have the annoying habit of popping off. The metal pins now keep all of the doors in place without preventing the hinges from detaching or wiggling. This was vitally important for the locking mechanism on the front door as it had to line up exactly in order to work.

Painting the beast!

I started the painting process by separating and cleaning all of the components, making sure to remove any detritus or residue on the panel surfaces as this model needed quite a clean look. First I sprayed all of the components all over with a plastic primer. This is always a necessary step when painting toy plastics as they generally do not take paint well. If you don't use a dedicated plastic primer, it is quite likely that the paint will chip and peel away, ruining all of your hard work!

Once the primer had thoroughly cured, I gave all of the internal parts a dark grey base spray and all of the outside armour plating a muted brown basecoat spray.
 
Once the basecoats were bone dry, I applied some black and brown washes to all of the grey areas, then highlighted them up to a nice light blue-grey colour. I also painted in some details on the wall panels such as little computer console screens while I could still reach all of the components.

Following the work on the internal details, I permanently reassembled the MTT with screws and epoxy glue to ensure that components were solidly fixed in place. I was also able to finally close up the hull around the new metal pins to ensure that all door and compartment covers were nice and secure while still being movable.


Having looked closely at reference for the MTT, I added different shades of brown as depicted in the film, paying careful attention to the smaller panel variations. Even though the whole tank is brown, there are lots of subtle tones which help to highlight the overall shape and pick out some details. I heavily weathered the vehicle and used pin-washes to redefine all of the panel lines. This was probably the second most time consuming part of the paint work!

Once I'd finished the pin washes and added spot details to some of the mechanical components (such as the engine details and mandible guns), I applied very fine metallic chip detailing with a small brush. This was the stage which took the longest, but it also better defined the panels and really pulled everything together!

The completed MTT Transport!

In total, the transport capacity of this monster is:

56 B1 Battle Droids in the main forward bay (25 on the lower and 31 on the upper level)
9 B2 Battle Droids in the upper rear compartment
4 deployed Droidekas in the forward top compartment
4 ball mode Droidekas in the central rear bay
1 DSD1 Dwarf Spider Droid in the central rear bay
1 General Grievous on his platform at the back of the central rear bay
4 STAP riders in the central rear bay (can alternatively hold 12 regular troopers)
12 additional trooper slots between the two flank bays

The following images show the MTT with the rest of my Separatist Droid army where I think it looks right at home!

No comments:

Post a Comment